KS260EP (INTERGRATED HOSE NOT INCLUDED)
Vacuum Capacity: 220m3/h 1 Tool, 260m3/h 2 tools
Dimensions (cm): 60x55x(h)90
Weight: 26kg
Noise Level: 72dB (A)
Filter Surface: 2.1 m2
Electrical Sockets: 2
Max Tool Power: 2 tools 800W + 800 W, 1 Tool, 1600W
Air Fittings: 2
Max Air Capacity: 1450l/m
Bag Capacity: 7 KG
Mobile extraction unit equipped for simultaneous connection to two tools, both electric and pneumatic. Robust, stable and highly manoeuvrable machine
Powerful and reliable, each fitted with two 1000 W motors. Dual start-up system: 1) manual 2) automatic, with a significant energy saving
Optional selection of two speeds to optimize extraction according to the number of tools connected. Highly-efficient filter system thanks to dual protection. Pratical front door to simplify the access to the dust collection bag.
- Part Number:
- KS260EP
Rupes HE200 Mini Turbine Dust Extraction
30.04.2011-
CABLE 2.5MM 2C&E PER MTPART NUMBER: 9C3
-
BASE KS260EPPART NUMBER: 001.1106/C
-
EXTRACTION UNIT KS250-KS260PART NUMBER: 003.1105
-
MOTOR COVER KS260EPPART NUMBER: 004.1106
-
BOTTOM HANDLE BRACKET KS260EPART NUMBER: 005.1106
-
HEAD CLIP KS260EPPART NUMBER: 006.1106
-
SILENCER COMPLETE KS260EPPART NUMBER: 007.1106/C
-
COOLING DUCT COMPLETE KS260EPPART NUMBER: 008.1106/C
-
HATCH COMPLETE KS260EPPART NUMBER: 012.1105/C
-
CLIP FOR FILTER CLEANER KS260EPPART NUMBER: 012.1106
-
FILTER HOLDER HOOK KS260EPPART NUMBER: 013.1106
-
REAR AXLE KS260EPPART NUMBER: 014.1106
-
HANDLE KS260EPPART NUMBER: 015.1106
-
EXHAUST PIPE KS260EPPART NUMBER: 016.1106
-
UPPER GASKET FOR MOTOR KS260EPPART NUMBER: 018.1106
-
HOSE HOLDER KS260EPPART NUMBER: 024.1106
-
BOLT COMP FOR FILTER CLEANER KS260EPPART NUMBER: 026.1106/C
-
FILTER SHAKER SPINDLE COMP KS260EPPART NUMBER: 027.1106/C
-
TAPPO PANNELLO COMANDI KS260EPPART NUMBER: 036.1106
-
TOP BRACKET FOR HANDLE KS260EPPART NUMBER: 047.1106
-
BRUSH S145/KS260 SELL X 2PART NUMBER: 090.1108
-
AIR VALVE KS260EPPART NUMBER: 45.90.100
-
PRESSURE SWITCH FOR KS260EP & S235EPPART NUMBER: 45.90.200
-
BRUSH HOLDER,BRUSH & SCREWS FOR 9GE07010PART NUMBER: 462.1106/C
-
REAR WHEEL COMPLETE KS ETCPART NUMBER: 9.E207/C
-
MOTOR KS260EP 230VPART NUMBER: 9GE07015
-
ELECTRONIC MODULE KS260EPPART NUMBER: 9GE08011
-
KS260EP AUTO20/MANUAL SWITCHPART NUMBER: 9GE09011
-
INDICATOR LAMP FOR KS260EPPART NUMBER: 9GE10009
-
REAR WHEEL COMPLETE KS260EPPART NUMBER: 9GM06027/C
-
RUBBER STRINGS KS260EP TOP COVERPART NUMBER: 011.1106
-
AIR INLET FITTINGPART NUMBER: 073.1606/C
-
MOTOR KS260 W/BRUSHES 462.1106PART NUMBER: 9GE07010
Dust extraction bag capacity
Dust extraction bags need to be checked and replaced regularly. There is a common misconception that a dust extraction bag does not need to be changed until the volume of the bag is full. This is not correct; the capacity of a dust bag is roughly 1/3 of its total volume. This is due to the compression effect of settled dust.
If you fill bags beyond this level you will run the risk of rupturing the bag which wall cause dust to clog the filter and get into the internal components of the dust extractor. If this occurs, at a minimum you will have a very messy clean up job and will likely need to replace the filter, and at worst damage the electrical components of the dust extractor to the point of rendering it inoperable. You will not be covered under warranty if the cause of damage is the result of a ruptured bag from over filling.
Below is an example of what a ruptured bag will do to the internals of your dust extractor. The filter on the left is new, the filter on the right is from a dust extractor with a ruptured bag.
